FeCoCrCuNi高熵合金裂纹及孔洞结构力学与微观构象演化机理的分子动力学模拟研究

本文采用分子动力学方法研究了FeCoCrCuNi高熵合金裂纹及孔洞模型结构在不同轴向拉伸应变速率下的力学与微观结构演化机理. 结果表明：应变速率越高FeCoCrCuNi裂纹结构对应更高的过冲应变和过冲应力，其主要原因是高拉伸速率会导致高强度的BCC结构及孪晶结构的生成，而BCC结构及孪晶结构的产生进而会抑制应力的下降，通过应力-应变曲线，可知FeCoCrCuNi裂纹模型在轴向应力作用下表现为塑性形变. 对于不同尺寸的孔洞FeCoCrCuNi裂纹模型的应力模拟与结构分析，可以得出：孔洞尺寸越大, FeCoCrCuNi裂纹结构对应的过冲应变和过冲应力越小，其主要原因是大尺寸的孔洞造成孔洞之间产生裂纹的，进而会影响这个材料的屈服应变和屈服强度.     

A Closed‐Loop Control Strategy for Producing Nitrile Rubber of Uniform Chemical Composition in a Semibatch Reactor: A Simulation Study

To improve the quality of industrial nitrile rubbers, the copolymer chemical composition, p_A(t), should ideally be kept constant along the reaction. This work proposes a closed‐loop control strategy for the semibatch operation of the reactor with the aim of regulating p_A(t) within a reduced range of variability. The proposed strategy is evaluated by simulating a mathematical model of the process. To this effect, a simplified mathematical model of the reaction is first derived and then utilized to obtain a suboptimal control law and a soft‐sensor that estimates the polymerization rates. The suboptimal control law is compensated by adding a term proportional to errors in p_A(t). The simulated example considers the production of the low‐composition AJLT grade, with the copolymerization reaction represented by a detailed mathematical model adjusted to an industrial plant. Due to the high performance of the soft‐sensor, the simulation results suggest that the proposed closed‐loop strategy is efficient to adequately regulate p_A(t) in spite of structural and parametric uncertainties, while other quality variables remained practically unaffected.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

水力劈裂问题的态型近场动力学建模

将态型近场动力学理论引入水力劈裂问题的模拟。构建了能反映岩土类材料准脆性断裂特征的态型近场动力学本构模型,并在物质点间相互作用力模型中加入等效水压力项,以实现在新生裂纹面上跟踪施加水压力。同时,考虑裂纹面间的接触,引入物质点间的短程排斥力作用,并设计了相应的接触算法。通过自编程序将模型和算法应用于含初始裂纹、不含初始裂纹以及含坝基软弱结构面的混凝土重力坝在高水头作用下的水力劈裂过程模拟,并与扩展有限元等模拟结果对比,验证了本文模型和算法的可行性和准确性。     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

Sufficient Conditions for a Digraph to be Supereulerian

A (di)graph is supereulerian if it contains a spanning eulerian sub(di)graph. This property is a relaxation of hamiltonicity. Inspired by this analogy with hamiltonian cycles and by similar results in supereulerian graph theory, we analyze a number of sufficient Ore type conditions for a digraph to be supereulerian. Furthermore, we study the following conjecture due to Thomassé and the first author: if the arc‐connectivity of a digraph is not smaller than its independence number, then the digraph is supereulerian. As a support for this conjecture we prove it for digraphs that are semicomplete multipartite or quasitransitive and verify the analogous statement for undirected graphs.     

一种经验型疲劳小裂纹扩展模型

金属材料疲劳寿命由裂纹萌生和裂纹扩展寿命两部分组成，其中对于萌生寿命中的小裂纹分析是精确描述裂纹萌生寿命的关键．而小裂纹在扩展过程中由于尺寸相对较小，导致传统线弹性断裂力学预测方法失效，需要对其进行改进，考虑裂纹尖端塑性区引起的残余压应力对小裂纹扩展速度的影响．本文针对此问题进行了初步分析，通过对塑性区引起的残余应力的量化，结合小裂纹门槛值特性，提出了一种经验型修正的小裂纹扩展模型，用于定量预测裂纹的萌生寿命．使用铝合金6082-T6缺口试样进行了疲劳实验，并与理论结果进行了对比，验证了所提模型的有效性．